PowerGlide™ AMD II (Concealed) Sliding Door Operator
Installation, Adjustment & Troubleshooting Manual
Document: US23-0222-01
Publication Date: October 1, 1999
Manufacturer: Besam Automated Entrance Systems, Inc.
Compliance: ANSI/BHMA A156.10-1999, UL 325 Listed
Applications include:
- Pedestrian entrances
- Schools & colleges
- Medical centers
- Office buildings
- Pharmacies
- Residential buildings
- Shopping malls
- Specialty installations
Safety Notice
Improperly adjusted doors can cause injury and equipment damage.
Important Safety Requirements
- Inspect door operation daily.
- Ensure all safety devices are operational.
- Have the door inspected annually by an AAADM inspector.
- Disconnect power before servicing.
Table of Contents
- Important Information
- Technical Specifications
- Introduction
- Models
- Parts Identification
- Space Requirements
- Installation Procedures
- Electrical Connections
- Wiring & Control Units
- Adjustments & Programming
- Troubleshooting
- Maintenance
- ANSI/BHMA Reference
- Parts List
Technical Specifications
Specification | Value |
Power Supply | 120V AC ±10%, 60Hz |
Breaker | 10A per operator |
Power Consumption | Max 250W |
Auxiliary Voltage | 18V DC, 0.5A |
Control Fuse | 2A |
Motor Fuse | 5A |
Door Travel | 35.5″ – 118″ |
Opening Speed | Up to 4.5 ft/sec |
Low Speed | Up to 1 ft/sec |
Hold Open Time | 0–60 seconds |
Temperature Range | -30°F to 113°F |
Max Door Weight | 440 lb (single leaf) |
Introduction
The PowerGlide AMD II is a concealed overhead sliding door operator designed for automatic pedestrian doors. It installs between two vertical jambs and supports:
- Sliding doors
- Fixed sidelites
- Optional transom systems
The system includes:
- Motor
- Gearbox
- Control unit
- Transmission rods
- Tooth belt drive
- Optional battery backup
- Optional locking devices
Safety sensors such as the Besam Eye-Cue MWD can be integrated for enhanced protection.
Available Models
Bi-Parting Models
Model | Opening Width | Overall Width |
AMD II-2-8 | 36″ | 96″ |
AMD II-2-10 | 48″ | 120″ |
AMD II-2-12 | 60″ | 144″ |
AMD II-2-14 | 72″ | 168″ |
Single Slide Models
Model | Opening Width | Overall Width |
AMD II-7 | 35.25″ | 84″ |
AMD II-8 | 41.25″ | 96″ |
AMD II-8-6 | 44.25″ | 102″ |
Main Components
The PowerGlide AMD II includes:
- Header
- Door Stop
- Cover Bracket
- Cover
- Drive Unit Brackets
- Carriage Wheel Bracket
- Door Carrier
- Transmission Rod Attachment
- Door Drive Bracket
- Cable Shelf
- Junction Box
- Cable Inlet
- Drive Unit
- Drive Wheel
- Gear Box
- Motor Unit
- Revolution Counter
- Optional Battery Unit
- Control Unit
- Optional Locking Device
- Tooth Belt
- Tension Wheel
- Cable Channel
- Floor Guide Track
- Program Selector
Installation Overview
Step 1 — Prepare Opening
- Ensure rough opening is plumb and square.
- Floor variation must not exceed 3/8″.
Step 2 — Install Header & Jambs
- Mount header to jamb tubes.
- Level and shim properly.
- Secure using recommended anchors.
Step 3 — Install Floor Guides
Options include:
- Full Breakout (FBO)
- Fixed Sidelite (FSL)
- Non-Panic guide systems
Step 4 — Hang Door Panels
- Install carriage wheels.
- Adjust height and alignment.
Step 5 — Install Drive Unit
- Mount drive module.
- Install transmission rods.
- Attach tooth belt.
Step 6 — Wire Control Unit
- Connect activation devices.
- Connect motor and optional battery backup.
Step 7 — Program & Adjust
- Set speeds
- Configure hold-open times
- Verify safety compliance
Floor Guide Systems
Available Guide Types
- Pin Guide (FBO)
- Roller Guide (FSL)
- Non-Panic Guide
Installation Notes
- Guides must be perfectly level.
- Use sealant beneath tracks when possible.
- All fasteners must be countersunk.
Door Adjustments
Height Adjustment
Raise door leaf approximately 5/16″ above floor.
Anti-Riser Wheel Adjustment
- Adjust until lightly touching underside of header flange.
- Back off approximately 1/32″.
Depth Adjustment
Adjust carriage wheel fittings for proper panel alignment.
Access Control Packages
Available Security Packages
- Package A
- Package B
- Package C
- Package D
Features may include:
- Panic devices
- Electronic carriage locks
- Battery backup
- Motion detectors
- Remote access control panels
Program Switch Modes
Mode | Function |
OFF | Doors locked |
EXIT | Exit only |
AUTO | Full automatic operation |
ENERGY SAVING | Reduced opening width |
OPEN | Hold-open mode |
RESET | System reset |
Control Units
CUD-9 (Programmable)
Features PMD programming module.
Adjustable:
- Opening speed
- Closing speed
- Hold-open time
- Partial opening width
- Lock timing
- Emergency functions
CUJ-9 (Potentiometer-Based)
Manual adjustment using onboard potentiometers.
PMD Programming Module
The PMD allows:
- Function programming
- Performance tuning
- Copying settings between operators
- Diagnostic monitoring
Functions include:
- Opening speed
- Closing speed
- Hold-open time
- Emergency behavior
- Locking controls
- Run programs
Maintenance Checklist
Regular maintenance should include:
- Inspecting safety sensors
- Checking belt tension
- Verifying breakout operation
- Inspecting guides and rollers
- Testing emergency battery operation
- Checking all fasteners
ANSI/BHMA Safety Compliance
The PowerGlide AMD II complies with ANSI/BHMA A156.10 standards for automatic pedestrian doors.
Adjustments must always:
- Prevent finger traps
- Maintain safe opening/closing speeds
- Ensure safe breakout operation
Troubleshooting Overview
Common troubleshooting areas:
- Motor direction
- Belt tension
- Safety sensor alignment
- Breakout switch wiring
- Lock device configuration
- Speed adjustment
- Controller error codes